design temperature

英 [dɪˈzaɪn ˈtemprətʃə(r)] 美 [dɪˈzaɪn ˈtemprətʃər]

设计温度

化学



双语例句

  1. The Research and Design of Temperature's Automatic Control System on Microwave Heater
    微波加热器温度自动控制系统的研究与设计
  2. A typical air-cooled direct bearing on the selection of annual air-cooled power plant design temperature and the temperature determine the full-fat.
    空冷典型年的选取直接关系着空冷电厂的设计气温和满发气温的确定。
  3. FPGA design in temperature monitoring system for diffusion furnace
    扩散炉温度自动控制系统中的FPGA设计
  4. But for full load generating equipments all year round, outdoor design temperature for summer ventilation is not suitable for room ventilation cooling.
    但是,对于常年全负荷运行的发电设备而言,如果机房内是采用通风换气降温时,不能错误的采用夏季室外通风计算温度。
  5. When design temperature or MDMT cannot coincide with the maximum pressure, the corresponding design pressure shall be designated together with the temperature.
    当设计温度或最小设计金属温度与最大压力不符,应根据温度指定相应的设计压力。
  6. When the indoor temperature reaches the design temperature, it transfers to one machine operation.
    当室内温度到达设定温度后,转为一台机工作;
  7. Design of Temperature and Humidity Measuring-System Based on CAN-Bus Intelligent Node
    基于CAN总线的智能温湿度检测系统设计
  8. Design of temperature control system of diode laser based on ARM
    基于ARM的半导体激光精确控温系统的研制
  9. Design of Temperature Control System for Perfusion Hyperthermia Based on MCU and FPGA
    基于MCU和FPGA的热疗系统控温仪设计
  10. Design of Temperature Control System for Microwave Heater Based on PLC
    基于PLC的微波加热器温度控制系统设计
  11. So, selecting a proper design temperature and pressure will be beneficial to the cost of pressure vessel and its saf.
    在相应设计压力下,容器壳壁及其元件可能达到的最高或最低工作温度为设计温度。
  12. Design Temperature and Material Selection for Large Scale Storage without Heat Input
    无热媒输入大型储罐的设计温度及材质选择
  13. Design of temperature control system for small diameter saw blade sintering furnace based on S7-200 PLC
    基于S7-200PLC的小锯片连续烧结炉温度控制系统的设计
  14. The paper introduces closing body design, temperature control design, and responding construction methods.
    本文主要介绍导流隧洞堵体设计、温控设计及相应的施工措施。
  15. System Design and Temperature Affection Analysis of a Capacitive Micro-accelerometer
    一种电容式微加速度计的系统设计与温度影响分析
  16. Design of temperature controller based on ARM and CPLD
    基于ARM和CPLD的温度控制器的设计
  17. Design of temperature alarm system based on OSGi service gateway
    基于OSGi服务网关的温度报警系统的设计
  18. The Design of Temperature Monitoring System Based on Sensor and SCM
    基于传感器与单片机温度监控系统的设计
  19. We Design a temperature control system of MEMS gyroscope which face to Pico-Satellite application, the principle is based on ADN8831 and TEC.
    设计了一种面向皮卫星应用的MEMS陀螺温度控制系统,其控制原理为基于ADN8831的TEC温度控制。
  20. Design of temperature monitoring system for high-voltage equipment based on wireless communication
    基于无线通信的高压设备温度监测系统的设计
  21. Design of Temperature and Humidity Monitor System with CAN Bus
    基于CAN总线温湿度监控系统的设计
  22. Discussion on Statistical Method of Winter Ventilation Design Temperature
    对冬季通风室外计算参数统计方法的讨论
  23. With special air circulation design, temperature is evenly distributed;
    特殊送风循环设计,温度分布均匀性佳;
  24. On Design Temperature of Metro System By Using Relative Warmth Index
    利用相对热流指标对地铁系统设计温度的探讨
  25. Then, the heating load and heat loss of the room with two systems in three typical city were calculated respectively under the condition that the indoor air design temperature of radiant floor heating is 2 ℃ lower than that of radiator heating.
    文章在低温地板辐射供暖室比散热器供暖房间室内设计温度降低2℃的情况下,分别对三个典型地区这两种供暖方式在上述情况下造成的房间热负荷和供暖季平均耗热量进行计算。
  26. Determination of heat medium design temperature in the Design standard for energy efficiency of residential buildings refers to the basic parameters of the heating system, and the understanding about the thermal performance of plastic pipes.
    《居住建筑节能设计标准》征求意见稿中关于散热器热水供暖系统设计温度的设定,涉及到供暖系统设计的基本参数,也涉及到对塑料类管材耐热性的认识和理解。
  27. Establishment of design temperature outside and analysis of maximum heating load of Multi-Span Greenhouse in China
    中国连栋温室室外设计温度确定及最大热负荷分布
  28. The application of titanium vessel in domestic, the active manufacture standard and the titanium's design pressure, design temperature and safety factor were discussed.
    论述了钛设备在国内的应用,介绍了现行的钛容器制造技术标准及各种钛材的最高设计压力、设计温度和安全系数。